Independently Owned Since 1996 · NICET-Certified · FM Global Experience
Mon–Fri 8am–5pm · (770) 531-0587
Home / Services / Clean Agent & Special Hazard Suppression
When water would ruin what the fire didn’t, you need a system that stops the fire and leaves everything else untouched. ProTech Fire designs, installs, inspects, and maintains clean agent and special hazard suppression for the data centers, control rooms, and high-value facilities that cannot afford a sprinkler discharge.
Total-flooding clean agent protects servers, storage arrays, and network gear without the water damage a sprinkler head would cause.
Switchgear, MDF/IDF closets, and petrochemical control rooms stay online because the agent is non-conductive and residue-free.
Records vaults, medical imaging, telecom huts, and clean rooms get fast knockdown that protects irreplaceable or sensitive contents.
A clean agent fire suppression system is an engineered gaseous system that detects a fire in its earliest stage and floods the protected room with a non-conductive extinguishing agent. The agent puts the fire out in seconds — usually before a sprinkler would even activate — and then clears without leaving residue, water, or corrosive byproducts behind. That is the whole point: in a room full of live electronics or irreplaceable records, the suppression system itself cannot become the second disaster.
Clean agents work by interrupting the fire in one of two ways. Chemical agents like FM-200 and Novec 1230 absorb heat faster than the fire can produce it. Inert gases like Inergen lower the oxygen concentration just enough to stop combustion while staying breathable for the people in the room. Both approaches are designed, installed, and maintained to NFPA 2001, the Standard for Clean Agent Fire Extinguishing Systems.
No single agent is right for every room. The correct choice depends on what you are protecting, how the space is occupied, local code, and your environmental priorities. We size and specify each of these:
If a water discharge would cost you more than the fire, you are a candidate. We most often install and service these systems for data centers and server rooms, telecommunications and network closets, switchgear and electrical rooms, petrochemical control rooms, medical imaging suites, laboratories and clean rooms, museums, and records archives. These are the facilities where downtime is measured in dollars per minute and the contents cannot simply be hosed down and replaced.
Clean agent suppression does not replace water-based protection everywhere — it complements it. A warehouse or a loading dock is still best served by sprinklers. A flammable-liquid hazard may call for foam suppression. Clean agent earns its premium in the specific rooms where a non-conductive, residue-free agent protects high-value or mission-critical assets. Many of the facilities we work with run all three, zoned so each hazard gets the right agent. If you are not sure which system a space needs, our consulting and design-build team will model the hazard and specify it properly.
A clean agent system only protects you if it will actually reach and hold the design concentration when it discharges. NFPA 2001 builds the whole lifecycle around proving that it will:
We handle this the same disciplined way we run every inspection program — documentation first, deficiencies flagged in plain language, and a clear path to correction.
Halon 1301 was the original clean agent, and plenty of older Georgia facilities still run it. Halon production was phased out under the Montreal Protocol, which makes recharging an aging system expensive and uncertain. If you are nursing a legacy Halon system, we can engineer a modern FM-200, Novec 1230, or inert-gas replacement that reuses as much of your existing detection and enclosure as possible, and decommission the old agent responsibly.
ProTech Fire is an independent, woman-owned company that has worked exclusively in commercial and industrial fire protection since 1996. Special hazard work rewards that focus — a clean agent system is only as good as the engineer who sized it and the technician who tests the room. Our NICET-certified team knows how Georgia’s fire marshals review these systems, and because we are independent and not part of a national roll-up, the same people stay on your building year after year. You get one accountable team for design, installation, and the inspections that follow, instead of a different subcontractor for each phase.
A clean agent fire suppression system is an engineered gaseous system that floods a protected room with a non-conductive, residue-free extinguishing agent — such as FM-200, Novec 1230, or inert gas — to put out a fire in seconds without water. It is used where a sprinkler discharge would damage high-value or mission-critical contents, like data centers, control rooms, and archives. These systems are designed and maintained to NFPA 2001.
It depends on the room and your priorities. FM-200 (HFC-227ea) is compact and fast, a strong fit where cylinder space is limited. Novec 1230 (FK-5-1-12) has a near-zero global warming potential and is the usual choice when sustainability drives the specification. Inert gas such as Inergen extinguishes by reducing oxygen and suits very large or occupied volumes. ProTech Fire models your hazard and specifies the right agent rather than defaulting to one product.
Under NFPA 2001, clean agent systems require semi-annual and annual inspections of the cylinders, detection, releasing panels, hoses, and nozzles, plus recurring room-integrity (door-fan) testing to confirm the enclosure still holds the agent. Agent cylinders also require hydrostatic testing on the NFPA interval. ProTech Fire schedules and documents each of these so your system stays compliant and discharge-ready.
Yes, when they are designed correctly. Agents like FM-200, Novec 1230, and inert gas are engineered to extinguish fire at concentrations that remain safe for people at the design level, which is why they are used in occupied data centers and control rooms. CO2 systems are the exception — they are intended for normally unoccupied hazards and carry specific safety requirements under NFPA 12.
Halon 1301 production was phased out under the Montreal Protocol, so recharging an aging Halon system is costly and increasingly impractical. You are not legally required to remove a working system, but most facilities replace it when a recharge is due. ProTech Fire can assess your Halon system and engineer a modern FM-200, Novec 1230, or inert-gas replacement that reuses as much existing detection and enclosure as possible.
Call ProTech Fire at (770) 531-0587 or request service through our contact page. We will evaluate the room, the hazard, and your compliance history, then provide an engineered design or an inspection and maintenance plan built around your facility. We serve commercial and industrial clients across Gainesville, Hall County, North Georgia, and the Atlanta metro.
Get a clean agent or special hazard system designed, installed, inspected, and kept discharge-ready by one independent commercial fire protection team.
The same fire protection team. Every year. Independent commercial fire protection, inspection, and foam testing across North Georgia and the Southeast since 1996.
Get an independent ITM quote or request an industry-specific assessment.
© 2026 ProTech Fire, Inc. · Gainesville, GA · All rights reserved.
ECH2O® · ENVIROFLO® · Planit-Safe® are trademarks of ProTech Fire, Inc.